That doesn't work, I am going to try uninstalling and reinstalling with cache and loud.
Uninstalling and reinstalling did nothing.
Uninstalling and reinstalling did nothing.
Last edited:
New CodeProject.AI License Plate Recognition (YOLO11) Module
- Thread starter MikeLud1
- Start date
Hey Mike,
Seems to be starting correctly now, I manually selected Device 0 and the log looks like this now:
But I am getting 0 calls to it. I haven't changed anything since I had 1.0.0.
These are my globabl BI AI settings:
These are the camera specific settings:
Thanks again!
Seems to be starting correctly now, I manually selected Device 0 and the log looks like this now:
But I am getting 0 calls to it. I haven't changed anything since I had 1.0.0.
These are my globabl BI AI settings:
These are the camera specific settings:
Thanks again!
Attachments
You are trying to do to much with one camera, create a clone of this camera and use it for just ALPR and the main camera for just object detection.
Attachments
The module seems to be working:
I just need to sort out why it is not getting called anymore.
I am a relative noob to this, I will lookup what cloning a camera is about and see if I can sort this out. Previously the ALPR module was getting called nonstop on everything, now it's not getting called at all.
Edit: OK, Got it, I didn't realize I shouldn't be using the same camera for double duty, I've got a few cameras I will have to clone.
I just need to sort out why it is not getting called anymore.
I am a relative noob to this, I will lookup what cloning a camera is about and see if I can sort this out. Previously the ALPR module was getting called nonstop on everything, now it's not getting called at all.
Edit: OK, Got it, I didn't realize I shouldn't be using the same camera for double duty, I've got a few cameras I will have to clone.
Last edited:
If you are not getting any calls, try doing this:
Go to your BI main settings, and go to the AI tab:
Make sure your IP and port are correct. Then click on the AI Dashboard link to the right of that to confirm you can reach it.
Next, click on the 3 dots next to the "Use custom models" and see if you see something like this:
I think only license-plate is needed, but I had to select all of them.
Uncheck "use custom models". Now click ok and do a test. If you don't see CPAI request count increase, it's because something thinks there is no plate, and doesn't make an OCR request.
I might be 100% wrong, but I just got this working after a few hours of trial and error. I wanted to configure it so I can just change the IP of which CPAI to use w/o changing any camera settings, etc and the above worked for me.
Go to your BI main settings, and go to the AI tab:
Make sure your IP and port are correct. Then click on the AI Dashboard link to the right of that to confirm you can reach it.
Next, click on the 3 dots next to the "Use custom models" and see if you see something like this:
I think only license-plate is needed, but I had to select all of them.
Uncheck "use custom models". Now click ok and do a test. If you don't see CPAI request count increase, it's because something thinks there is no plate, and doesn't make an OCR request.
I might be 100% wrong, but I just got this working after a few hours of trial and error. I wanted to configure it so I can just change the IP of which CPAI to use w/o changing any camera settings, etc and the above worked for me.
Alright, ignore me, I gotta learn how to configure BI:
Something came through, I am getting calls to the Object Detection and the License Plate Detection.
I am now learning about how to setup dedicated cloned streams.
Thanks for all your help Mike!
Edit: Those detections are from me manually running the detect per Mike's request. I"m still setting up a cloned stream for the LPR.
Something came through, I am getting calls to the Object Detection and the License Plate Detection.
I am now learning about how to setup dedicated cloned streams.
Thanks for all your help Mike!
Edit: Those detections are from me manually running the detect per Mike's request. I"m still setting up a cloned stream for the LPR.
Alright, granted I learned about these two hours ago, but I have setup a cloned camera from my main stream. Disabled audio, disabled record, disabled motion/triggers, Alerted when Cameras in Group are Triggered, Confirm Alert with AI etc.
I confirmed this cloned camera RALPR gets triggered by the group, but it is just not sending anything to the ALPR module? The module still shows the 4 test detections I manually ran, but the cloned camera is still not sending anything to the ALPR module. I feel like I've got a setting wrong here but with all the changes to the gui it's hard to get Chat to sort it out.
Again, this all worked fine with v1.0.0 of this yolo11 module.
Trying to help!
I confirmed this cloned camera RALPR gets triggered by the group, but it is just not sending anything to the ALPR module? The module still shows the 4 test detections I manually ran, but the cloned camera is still not sending anything to the ALPR module. I feel like I've got a setting wrong here but with all the changes to the gui it's hard to get Chat to sort it out.
Again, this all worked fine with v1.0.0 of this yolo11 module.
Trying to help!
Attachments
I uninstalled v1.0.2 and installed v1.0.3. The module will not stay running more than about 5 seconds. After about 3 minutes or so it says "Failed to Start" and the YOLO11 bar is RED (see below). My GPU device shows up as GPU 0 in task manager (see below). I have tried manually selecting GPU Device 0 and that didn't help.
Hey Mike,
So nothing was working, I decided to reinstall the original appsettings.json file so I could reinstall the original ALPR module.
Once I installed and started the original ALPR module the new ALPR module you made started working all of a sudden.
Wild shot in the dark, the original module creates an alpr_queue that the new one is looking for but can't find if the other is uninstalled?
So nothing was working, I decided to reinstall the original appsettings.json file so I could reinstall the original ALPR module.
Once I installed and started the original ALPR module the new ALPR module you made started working all of a sudden.
Wild shot in the dark, the original module creates an alpr_queue that the new one is looking for but can't find if the other is uninstalled?
I couldn't get it working on a fresh install of CPAI either without first installing the original ALPR first, then shutting down CPAI, replace appsettings.json and then installing the new v1.03, but that could have been caused by something else entirely.