Same old crap works great all night then goes dead during the day. Brand new cat 6 cable and 12.6v from the power supply. It makes absolutely no sense.
Camera Freezes
- Thread starter Woody70
- Start date
So to clarify you shut down BI during the day, if so how are you determining that the camera goes dead, or is it dead when you restart BI in the evening. What happens if you leave BI running during the day?
Not sure about that one. I will leave it running tomorrow and see what happens. I did notice today I checked it about 9:30AM and it was dead, checked periodically through the day and it suddenly appeared again about 3PM. I use the program Advanced Port Scanner to check it because if it shows up dead in there it will definitely not show up in B.I. I'm sorry to keep bothering you guys about this, i think maybe I should just contact Zosi and see what they say. I did have problems with this camera right after I bought it and they remotely updated the firmware on it for me and it has worked fine until this problem. I'll see what it does tomorrow leaving it running.
I suspect that you may be right, moist likely some sort of fault with the camera, If the camera keeps working with BI running all day, then I would suspect some sort of built in energy management that you have no control over, lets see what happens!
Well it did the same thing with leaving B.I. running. I checked it about 10:30Am and it was dead, came back on around 1:30PM and went dead again around 2PM. I checked the voltage all the way to the camera and it is good. I even replaced it with a 2amp instead of the 1amp 12v power supply to no avail. I'm going to order a ethernet cable tester (my wife was supposed to order it 4 days ago and didn't) just to make sure it is not that before I contact Zosi. I highly doubt that is the problem though because it is brand new cat 6 cable, only about two months old. I will advise when I get the results. Thank you all for the time and advice you have given me, it is much appreciated.
Well I haven't got my tester yet but I did switch the camera over to wireless two days ago and it has not gone dead. It does lose connection sometimes for a minute or so I'm sure because of it being wireless. I guess that tells me the camera is ok I'm not sure. I will check the cable when my tester gets here, should be tomorrow.
Ok the cable tested good so I don't know what is wrong. It does better wireless than wired except for the video freezing. Could the ethernet cable next to the power cable for only about three feet be a problem? It is unshielded cable. But it works good all night.
I am not sure what else to suggest, I have never encountered that sort of issue, it has always been a bad camera or a damaged Ethernet cable!
That's what bugs me. It worked and didn't lose connection when connected to the router, the video would freeze sometimes is what I was asking about from the start and it was suggested to use a NIC switch to solve that and it seemed to do that. But that is when it would go dead for hours and then reappear suddenly. So I will just deal with it freezing I guess. Thank you all for all the help you did suggest anyway.
Try plugging it back in to the router again, it makes no sense to me!
Last edited:
That's what I did a few days ago and it has not gone dead after that. I have noticed though after I shut down B.i. I then connect to IP Cam Viewer in the mornings just to be able to view what is going on and it seems like when I shut it down and switch back to B.I. the camera is not there. I know it could only happen to me something this crazy. Anyway I will keep playing with it and see what happens.
It's been connected directly to my router the last few days so I'm sure it could find internet if it needed it. Everything I have been told is security cameras don't need internet. I think I will go ahead and contact the company and see what they have to say. One thing I can say about them is they have been very good in the past with their support.
From what I understand the only reason you need internet for a security camera is if you want to view them from anywhere or want alerts and so on. I just need them to record to my hard drive at nighttime and that's it.
Last edited:
Your Blue Iris machine may not have enough free resources for smooth playback on that camera. Or the stream from the camera's hardware is weak and glitchy. Or network hardware is slow somewhere.
I've seen that before on my earlier BI boxes.
One time I solved it by using 2 Hard drives and splitting the writes and reads across 2 disks,
to try and unchoke any bottlenecks associated with Spinning drives.
This resulted in a big improvement on my hardware back then, I think it was an i7-3770s FrankenDell 7010.
So now I run 2 WD PURZ drives.
Last edited: