Recent content by rdxny

  1. R

    Use a clone to have two different IVS areas alert differently?

    makes sense, and yes, you can filter for confirmed alerts in the console. I will try, see if it plays nice with my alerts (pushover) for main... thanks:) add: I think I would have to make the other cameras confirmed alerts also tho...
  2. R

    Use a clone to have two different IVS areas alert differently?

    This has been working great, thanks guys. One additional question: Since both the main and secondary IVS triggers end up in the clip list in BI at left, when using the "Alerts" filter, is there a way to assign something like "Flagged" automatically to the "main" IVS triggers so I only see them...
  3. R

    Use a clone to have two different IVS areas alert differently?

    Thanks:) I had the first two parts down ok, but I couldn't see a way to differentiate the two IVS rules in the Alert tab, I was missing #3, the "required AI objects" part, thinking that was only for the built-in BI AI or other external AI. That's the missing part that should allow me to...
  4. R

    Use a clone to have two different IVS areas alert differently?

    Thanks jrbeddow, I'm not using nvr, just the cameras IVS.. I think I'm ok with setting two different IVS rules, and having BI see them on onvif config. I'm simply trying to have both Tripwires record, but only one alert. I cant seem to see where I can tell alerts to pay attention to one onvif...
  5. R

    Use a clone to have two different IVS areas alert differently?

    Thanks wittaj, OK, not as simple as I thought (for me!) I created another rule for that cam as below: (with "road being the added rule I dont want alerts on) Then set BI Onvif But where do I tell BI to listen only to Road or Main? and where do I setup the alerts for one or the other, not...
  6. R

    Use a clone to have two different IVS areas alert differently?

    hmmm, simplicity always rules? I'll try that! Thanks:)
  7. R

    Use a clone to have two different IVS areas alert differently?

    I'm trying to do two different BI alerts from one t180 camera: The first is a "normal" IVS tripwire Onvif trigger that makes BI record mainstream, alerts Pushover, etc. All good there. The second is I'd like a different area of the same camera to trigger, causing a recording of main stream, but...
  8. R

    Detecting wildlife with Dahua cameras

    I Think that option to choose "which" animals is available on the Pro Cameras (like on my T5459-Pro) firmware, but not on the latest (R8) version of the T54IR-S3 cameras. At least that's what I see on my versions.
  9. R

    Detecting wildlife with Dahua cameras

    In the latest webUI, combined with the S3 Dahua (or Andy Cams), you do indeed see "animals" as a choice. I only use the cameras IVS rules as above, as opposed to CPAI or Blue Iris' latest built in AI, so I don't get any tagging as Dog or Cat, etc. The clips just say "Tripline" or "intrusion"...
  10. R

    Help with UI3 and Tailscale

    If I leave BI's IP address (192.168.1.xxx) in BI's webserver fields, and try to connect from outside with Tailscale running, and use TS's IP to connect to UI3, that works fine in or out, but alerts in Pushover show the alert, the thumb, but If I select UI3 or Hi Res in Pushover it tries to...
  11. R

    Powershell Script to Send Pushover Notifications with a Camera's or Cam Group's Current Image

    agreed. IF you don't see battery drain, then just leave it on and one shortcut to UI3 will work everywhere.
  12. R

    Powershell Script to Send Pushover Notifications with a Camera's or Cam Group's Current Image

    correct. You could turn Tailscale off on the phone, and just flip it on when needing to access UI3 if worried about drain. Tailscale support says it's an issue if running TS as Exit Mode... I do not.
  13. R

    Powershell Script to Send Pushover Notifications with a Camera's or Cam Group's Current Image

    I have an Android, and I have not noticed Tailscale running down my charge. It might , I just I haven't noticed or tested. (I did use Zerotier previously, and that also ran full time (well, sometimes after a reboot I needed to turn it back on), but I don't see a difference power wise. I do like...
  14. R

    Powershell Script to Send Pushover Notifications with a Camera's or Cam Group's Current Image

    I use my tailscale IP (100.69.xx.xx) in all the webserver fields... the Lan, Adapters, and WAN (though I don't think the WAN one matters) I see UI3 both on my home net (with tailscale running all the time) as well as away from home (again, with tailscale running on laptop, phone, etc) accessing...
  15. R

    Intermittent BI Crashes, usually middle of the night, assistance/thoughts please

    BI 6.0.5.0 had issues, including crashes. 6.0.5.1 now posted, fixed that (for me) . That may or may not be your issue, but start there!
See more
Top Bottom