I'm asking regarding this specific cable since it has free international shipping (and it says pure copper).
My only concern is that it seems as if it will hard to bent it - due to the white plastic that separates the wires.
Last edited:
Is this Cat 6 cable any good?
- Thread starter d5775927
- Start date
I'm asking regarding this specific cable since it has free international shipping (and it says pure copper).
My only concern is that it seems as if it will hard to bent it - due to the white plastic that separates the wires.
Broachoski
Getting comfortable
It is a reputable company and is sold in the North America by Lowes and Home Depot at higher price. All cat6 has the inner core and is not hard to handle. Doing tight bends is BAD for any ethernet cable. Ignore that 1 comment about it being hard to bend.
The price is good also.
The price is good also.
Last edited:
Just be diligent when purchasing the male RJ-45 connectors..... be sure they are for 23 AWG and for solid conductor.
Starglow
Getting comfortable
Sometimes if you're running additional Cat6 cable though an already existing access hole without much clearance due to other cables passing through, that Cat6 inner core can be the make or break different between whether that cable can fit though the hole or not. In those rare cases and assuming you can't drill a new adjacent hole I revert back to Cat5e cable which has no inner core so it's a smaller diameter and will usually fit through a tight space.
mat200
IPCT Contributor
- Jan 17, 2017
- 19,369
- 32,354
I'm far from the expert on shielding, and you may get more specific answers. My 30,000 foot take on using shielded cable is:
1. With twisted pair cable, it's rarely necessary.
2. Grounded and/or bonded incorrectly it makes matters worse.
3. Grounding and/or bonding correctly adds to the installation cost and labor.
1. With twisted pair cable, it's rarely necessary.
2. Grounded and/or bonded incorrectly it makes matters worse.
3. Grounding and/or bonding correctly adds to the installation cost and labor.
Good luck trying to get connectors on AWG23
I suggest only use AWG24 for cam installations. You can use passthrough connectors, which are quite easy to crimp.
store.ui.com
I suggest only use AWG24 for cam installations. You can use passthrough connectors, which are quite easy to crimp.
UniFi Outdoor Cable - Ubiquiti Store
Outdoor Category 5e cable designed to resist harsh weather damage and electromagnetic interference.
store.ui.com
I've crimped a couple hundred connectors on awg23 cat6 with no problem related to wire gauge. Just have to get connectors specified for cat6 cables, most of which are awg23.
mat200
IPCT Contributor
- Jan 17, 2017
- 19,369
- 32,354
my experience also .. solid coper 23 or 24 AWG in a typical RJ45 plug with no issues outside of the operator .. once I got the hang of it, works well ..
depends on how thick the insulation is.
i know in US there are lot of cables out of any certification just tested with a fluke.
but here you cannot buy this kind of china cable. most awg23 cables have thick insulation here in europe. if you want to put rj45 on, you have a hard time to find some which fit. there are some china aliexpress cheapos out, but they arent good. some hirose claim awg23 , but hard to get them togehter cause of the insulation. also some does not fit into waterproof connection of camera.
I have had great luck with CAT-6 using this method:
ipcamtalk.com
And I used the 2 piece RJ-45 for solid conductor with an insert to align the staggered conductors ==>> Monoprice Cat6 Plug Solid W/Insert 50U 100pcs/Bag
how to make good cat6 cables all the time
If anyone has purchased cat cables and planned on terminating themselves, especially with cat6 solid strand, check out these vids below. I couldn't figure out until this guy explained the wire guide correctly;
And I used the 2 piece RJ-45 for solid conductor with an insert to align the staggered conductors ==>> Monoprice Cat6 Plug Solid W/Insert 50U 100pcs/Bag