Search results

  1. ron351

    New ALPR - Do not want any monthly fee.

    Ok thank you appreciate the reply
  2. ron351

    New ALPR - Do not want any monthly fee.

    You mention free Protect software I can not find that on their site. Is the software built into the NVR you listed? Do you have this setup and if so does it have a database of license plates it captured?
  3. ron351

    Issue connecting to cameras without a router

    Ok guess it threw mw where you said all your devices are wireless in your 3rd post No, I did not connect anything to the new router when I swapped it in. All my devices are wireless. So, the router is just connected to the modem. As for the POE switch. Those cables did not change (camera cables...
  4. ron351

    ip address not showing in camera list

    I missed where you said the cameras are wired to the NVR. In network settings try changing it to DHCP if the IP is Static IP and see if the cameras come up. That would be the easiest thing to try. The NVR has it's own POE output and usually that don't go bad. If your NVR does get a IP address...
  5. ron351

    Issue connecting to cameras without a router

    Don't know if this is resolved or not but you say your cameras are wireless but connected to the poe switch. Assume your only using the poe switch to power the cameras then and not connect to a network with a router? I would assume you need a router no? And you mention you don't need it online...
  6. ron351

    Corner Mount Bracket Installation Best Practice Advice Request

    Even if the bracket goes beyond the stud usually there is 3/4 board on houses except the newer house that use the particle board. Use galvanized lag screws is what I would use. The weight will be on the top lags so if they tighten good then you will be fine if not maybe shove an anchor in then...
  7. ron351

    ip address not showing in camera list

    Just chiming in is the cameras set to static IP addresses? If power failed and rebooted everything maybe the IP address has changed. I use Advanced IP Scanner to see what all is on the network. Best to always jot down the MAC address so it is easier to locate on the IP Scan
  8. ron351

    Point to Point Wireless Bridge Recomendations

    That would work just fine but like others said priced to high. I have a few installed at apartment buildings and they have had no issues and one is around 950 feet away
  9. ron351

    POE Turret camera for Honeywell HEN16122 model NVR compatible low cost

    Anyone familiar with the POE Honeywell NVR model HEN16122 and a low priced turret camera that is compatible with that model NVR? Even a 2MP camera will work it is inside an office so it don't need to be a expensive camera. I find Honeywell makes are picky on what cameras are compatible and what...
  10. ron351

    Needing an outdoor PoE setup cameras

    With bushes triggering motion sounds like you used motion detection. Trip wire cameras are less false triggers. I only deal with 4K cameras with audio. Get a 16 channel NVR with at least 10TB HDD and use 4K cameras.
  11. ron351

    Dahua has a new water proof junction box PFA130-E / PFA130E for Turrets ( PFA137, PFA139 )

    Says M4 on the diagram
  12. ron351

    Point to Point Wireless Bridge Recomendations

    I have 2 large apartment complexes with 4K cameras on a wireless Ubiquity bridge. Distance is 825 feet for 1 place and 600 feet at the other. The receiving end I have a 8 port POE switch with uplink and the uplink goes another 200 feet to another POE 8 port switch and there are 11 4K cameras on...
  13. ron351

    Installing ethernet wire from 14-foot eaves soffit to 8-foot camera height

    You have power to the lights if they turn on by light sensor there should be constant power before the sensor, tap off that.
  14. ron351

    Installing ethernet wire from 14-foot eaves soffit to 8-foot camera height

    I have used the 12" boxes and enough room to put a poe switch in it and mounted 3 cameras to get all around view and ethernet cables from camers reach right into the poe switch. Makes easy install of multiple cameras. Just a thought.
  15. ron351

    Installing ethernet wire from 14-foot eaves soffit to 8-foot camera height

    I usually break the ears off with plyers and screw boxes through the back of the box into the surface
  16. ron351

    Installing ethernet wire from 14-foot eaves soffit to 8-foot camera height

    No crawl space above garage? Must have if the other camera is up there. I would try drilling down between the wall and push a fish stick through the insulation and string and try to snag it in a hole with a wire like coat hanger and the camera will cover the hole. Did a couple like that, takes...
  17. ron351

    Outdoor POE switch install

    I just put weatherproof boxes in large enough to put a 8 port POE switch and electrical outlet inside the box and one I attached the cameras also to the box. The other cameras were external from the box and always use the uplink switches so I can run a cat5 to the next box with a POE switch.
  18. ron351

    Ubiquity Wireless Bridge 4K cameras

    Never used RTSP for cameras, sounds good though.
  19. ron351

    Ubiquity Wireless Bridge 4K cameras

    First Ubiquity antenna is direct into the router and only 1 POE switch at the far end antenna. It should be fine.
  20. ron351

    Ubiquity Wireless Bridge 4K cameras

    Thank you I use the 5AC never used the PTMP
  21. ron351

    Ubiquity Wireless Bridge 4K cameras

    Keeping the bit rate at 4096 so at the 4096 bit rate and the ubiquity bridge can handle 450Mbps I am not a mathematician that was why I was asking.
  22. ron351

    Ubiquity Wireless Bridge 4K cameras

    Thank you, at least I have a idea now, I have 7 running now no issues. The VICE unit at my Police department wanted to know if I could add more on their monitoring, so will be adding a few more so they can gather the evidence they need. Thanks again, I was unsure how much each camera might use
  23. ron351

    Ubiquity Wireless Bridge 4K cameras

    I must be the only one I guess who is looking to see how many 4K cameras that can be added to the end run of a 450Mbps Ubiquity bridge on a POE switch. Was hoping someone knew how many Mb each 4K camera would use before the 450Mbps bridge would be full.
  24. ron351

    Ubiquity Wireless Bridge 4K cameras

    Curious as to the limit of 4K cameras that will work on the far end of a wireless bridge. I have a Ubiquity 450Mpps bridge now 450' at the other end of an apartment building with (7) 4K cameras working now out of a POE switch at the far end at the antenna receiving end and works fine. Had a...
  25. ron351

    How to get gigabit speeds?

    Talking gigabit here routers and switches are gigabit but what about the network cameras? I have not looked at specs on cameras but if the lights are yellow that is 100mbps and green is 1000mbps right? How is one to know if the camera is capable of gigabit speeds? Just curious
  26. ron351

    DESIGN

    I would add 4 more cameras 2 in the center on both sides of the long building criss crossed view to get better view of the center seeing distance from corners would be so faw away. Also a PTZ with auto tracking might be nice where it will zoom in automatically on motion and track movement then...
  27. ron351

    Just got this email from Rekor

    All you can do is try if the current one is not working right. I never used anything but the I7 processor that came with the laptop
  28. ron351

    Just got this email from Rekor

    Here is what else they wrote: While we will always recommend to upgrade to the newest version. If the old one is working for you, I would keep an eye on it until you see an issue and then upgrade to 4.1.3 if you absolutely have to. The reason I say that is because I've noticed some customers...
  29. ron351

    Just got this email from Rekor

    I guess if no issues you don't need to. They just said they fixed the bug that people were getting with the agent stopping and having to restart it.
  30. ron351

    Just got this email from Rekor

    Recor got back with me and updated the page. Direct link is here if needed for 4.1.3 and so far working good and agent has not stopped. https://deb.openalpr.com/windows-agent/staging/openalpr-agent-4.1.3-signed.exe
Top Bottom