In Dahua, why doesn't the camera show when I assign the correct IP?

[Mark_M]

Change it here? 10.1.1.x on 192.168.x.x?View attachment 233481

Create ONVIF user login on the camera. Write down username and password.
Change the camera's IP address 10.1.1.150, subnet mask 255.255.255.000, gateway 10.1.1.1 .
Plug camera into NVR POE switch ports. Manually add camera by ONVIF and the IP 10.1.1.150.

 

[toyon]

Oh, so it's a Hikvision (or other 3rd party camera).
You'll need to manually setup ONVIF login, assign it a static IP within your NVRs switch 10.1.1.x range, then plug it in and manually configure.

TCP: 192.168.0.200
Switch: 192.168.1.111

Reset the camera, its IP became 192.168.1.108.
The second camera's IP is unknown, it assigns itself automatically and can be seen in the picture. The equipment was assigned an IP of 192.168.1.128.
Despite these changes, it's still not working.

 

[toyon]

Create ONVIF user login on the camera. Write down username and password.
Change the camera's IP address 10.1.1.150, subnet mask 255.255.255.000, gateway 10.1.1.1 .
Plug camera into NVR POE switch ports. Manually add camera by ONVIF and the IP 10.1.1.150.

ок

 

[Mark_M]

TCP: 192.168.0.200
Switch: 192.168.1.111

Reset the camera, its IP became 192.168.1.108.
The second camera's IP is unknown, it assigns itself automatically and can be seen in the picture. The equipment was assigned an IP of 192.168.1.128.
Despite these changes, it's still not working.

Why did you do that?
Changing the NVR switch to be the same IP range as the LAN port causes problems.
They need to be different IP addresses.


Do these settings:
NVR LAN (NIC1):
IP: 192.168.0.200
Mask: 255.255.255.000
Gateway: 192.168.0.1 (your router IP address)

NVR switch:
IP: 10.1.1.1
Mask: 255.255.255.000
Gateway: 10.1.1.1

Camera:
IP: 10.1.1.150
Mask: 255.255.255.000
Gateway: 10.1.1.1

 

[toyon]

Why did you do that?
Changing the NVR switch to be the same IP range as the LAN port causes problems.
They need to be different IP addresses.


Do these settings:
NVR LAN (NIC1):
IP: 192.168.0.200
Mask: 255.255.255.000
Gateway: 192.168.0.1 (your router IP address)

NVR switch:
IP: 10.1.1.1
Mask: 255.255.255.000
Gateway: 10.1.1.1

Camera:
IP: 10.1.1.150
Mask: 255.255.255.000
Gateway: 10.1.1.1

ок

 

[toyon]

Why did you do that?
Changing the NVR switch to be the same IP range as the LAN port causes problems.
They need to be different IP addresses.


Do these settings:
NVR LAN (NIC1):
IP: 192.168.0.200
Mask: 255.255.255.000
Gateway: 192.168.0.1 (your router IP address)

NVR switch:
IP: 10.1.1.1
Mask: 255.255.255.000
Gateway: 10.1.1.1

Camera:
IP: 10.1.1.150
Mask: 255.255.255.000
Gateway: 10.1.1.1

I did as instructed. On my laptop, I changed the camera’s IP to 10.1.1.150. Corrected the “switch” IP address too. However, the camera isn’t being detected automatically. When added manually, it still doesn’t work.

 

[Mark_M]

Make sure you selected ONVIF as the type. Not default "Private protocol".
I see the port is 3777 which is private protocol.

 

[toyon]

Make sure you selected ONVIF as the type. Not default "Private protocol".
I see the port is 3777 which is private protocol.

indeed, ONVIF helped.. the picture appeared.. the second camera doesn't work because I don't know the password, I'll reset it and I think everything will work. Thank you very much!

 

[bigredfish]

Make sure you selected ONVIF as the type. Not default "Private protocol".
I see the port is 3777 which is private protocol.

You sir have the patience of a Saint.

 

[Flintstone61]

I just confused things a little more, after an 11 hour workday From now on I be will calling on Saint @Mark_M