Search results

  1. L

    stunnel

    I would probably be using a similar setup i think, let me dig in and see if i can figure this out, just waiting for a weekend to get this started. Cheers
  2. L

    stunnel

    Got mine working finally with https! Thanks to you for that! I just had to correct the IP address routed to the correct one and the remote viewing worked on https. Now on to learning a bit more about alerts on blue iris and the best setting to go with.
  3. L

    stunnel

    Now i could be wrong as i am no expert but my understanding is that this allows videos transmitted over the internet to be encrypted when remotely viewed or so i think. blue iris encrypts user and password with https but not the video transmitted i believe, and this requires a stunner service...
  4. L

    stunnel

    Yes you are right, 8080 is port forwarded on the router to my laptop running Blue Iris. I am pretty sure i have the same above mentioned way of setup for external viewing on my router, i will double check once again and confirm as soon as i get the chance. I don't know much about VPN other than...
  5. L

    stunnel

    Thanks so much again johnmcc!!! Almost there!! This was it, i set up the certificate request completely during re-installation and the stunnel is running successfully now with just the following code updated to the config! [blue iris] accept = 8080 connect = 8081 cert = stunnel.pem Thanks...
  6. L

    stunnel

    Thanks so much, i do recall this step where i just gave . to all, may it matters to enter something? Let me try uninstalling and reinstalling, and enter some value rather than . for all. Will test this and get back to you!
  7. L

    stunnel

    Thanks once again johnmcc, I tried both cert = C:\Program Files (x86)\stunnel\config\stunnel.pem and C:/Program Files (x86)/stunnel/config/stunnel.pem and get the same error as follows, [ ] Loading certificate from file: C:\Program Files (x86)\stunnel\config\stunnel.pem [!] error queue...
  8. L

    stunnel

    Thanks for this, i will do a cross check of the statements and update soon. Cheers.
  9. L

    stunnel

    Yes the stunnel.pem is in the config directory, i did verify this while i was trying to verify if the certificate even exists.
  10. L

    stunnel

    Thanks johnmcc. I already did try stopping and restarting the service, but i got the same error. however for the line 'connect = ' i used the port number alone similar to 'accept = ' line. So i tried again putting the full ip address suffixed with colon port number hoping it would work - but no...
  11. L

    stunnel

    Thanks for responding. I tried the line requireCert = no instead of cert = stunnel.pem but i get following error message which still asks for a certificate. 2017.04.24 06:06:19 LOG5[main]: Reading configuration from file stunnel.conf 2017.04.24 06:06:19 LOG5[main]: UTF-8 byte order mark...
  12. L

    stunnel

    Yes I am editing from the GUI from the menu options. I must be missing something that is not very obvious. Just not working for me! Is there any other thread forum, where some expert can help?
  13. L

    stunnel

    #HELP - !!!
  14. L

    stunnel

    Tried to reset the code from stunnel: Windows Config The configuration loaded successfully. But again after inserting the below lines same error thrown. No difference to my earlier test results. ; ***************************************** Example TLS server mode services [blue-iris] accept =...
  15. L

    stunnel

    and without the below line, i get an error that a certificate is required, so i guess it needs to be there. cert = stunnel.pem
  16. L

    stunnel

    Frank, Thanks for the input, Yes i did test by removing/commenting the below lines, and the stunnel config file loads fine with no errors. [blue-iris] accept = 8151 connect = 8141 cert = stunnel.pem It is only when the above lines are inserted, the stunnel config reload fails. Also tried...
  17. L

    stunnel

    Have tried unchecking secure only on blue iris webserver - no change in behavior I tried the stunnel DN setup for personal certificate setup - this also renders same results. Not sure what else to try given that i am running trials based on advise over the internet, as i am no networking...
  18. L

    stunnel

    help anyone? would appreciate some guidance with the stunnel setup. Thanks!
  19. L

    stunnel

    Also tried the config lines below by putting it right under server section starting with comment ; ******************************************** Example TLS server mode services, still same error. [blue-iris] accept = 8151 connect = 8141 cert = stunnel.pem Error: Service [blue-iris]: Failed to...
  20. L

    stunnel

    Guys, Sorry for reopening this thread with a similar question on configuring stunnel for blue iris 4 running on my win 10 laptop. I have read through all comments on the 2 pages of this thread but somehow i think i am missing something as i can get the stunnel gui to load the configuration file...
  21. L

    Hikvision SADP Tool and Windows 10 Compatability Question

    I rebooted everything with lan cable connected, and for some reason this has helped. Now it is showing up on SADP tool, and also i was able to setup wireless using the internet explorer browser interface. Now need need to learn on good security settings for the wifi access. so much to get my...
  22. L

    Hikvision SADP Tool and Windows 10 Compatability Question

    I don't think the cameras is on wifi yet because the link led on the ip cam doesn't blink once the ethernet cable is disconnected. Even with the ethernet cable connected to the camera i am not able to see the camera on the SADP tool. I want to connect all of them wirelessly without ethernet...
  23. L

    Hikvision SADP Tool and Windows 10 Compatability Question

    I am not sure if there is a more relevant thread so posting for help here. I am a complete newbie to networks and cameras. I recently purchased the four HIKVISION DS-2CD2420F-IW IP cameras. I am running Windows 10 Home. When i start the SADP tool I can't see any cameras. WinPcap already...
Top Bottom