Search results
-
Another new OWL VIEW Camera Comparison
IPC2B14SE-ADF28(40)K-WP-I1 4MP WDR OwlView Plus Bullet Network Camera • High quality image with 4 MP, 1/1.8" CMOS sensor • 4 MP (2688 × 1520)@30/25 (default) fps; 4 MP (2560 × 1440)@30/25 fps; 3 MP (2304 × 1296)@30/25 fps; 1080P (1920 × 1080)@30/25 fps • Ultra 265, H.265, H.264, MJPEG •... -
Another new OWL VIEW Camera Comparison
These are the "factory" settings, I have not change them. -
Another new OWL VIEW Camera Comparison
Very much appreciate the help. I have been using the IR camera for past 3 years. The new to me Owl view have excellent daytime image and motion. Night with the IR cam is obviously limited in "range" due to the light from the IR. But the motion was much sharper. The color Owl View is quite... -
Another new OWL VIEW Camera Comparison
I am NEW to using BI and installing cameras. What I am looking for is a suggestion on SETTINGS which are many on the camera to offer good night vision and smooth as possible clarity for motion. The camera, I just put it up and it has it's "factory" out of the box settings. What do you... -
Another new OWL VIEW Camera Comparison
The motion settings I may need to tweak as I just installed the camera (plus drilled new holes for the mounting box) this evening. I probably need to set the frame rate and FPS etc. But I will play with that tomorrow. With the IR camera, (that I just removed) there was hardly any detail on... -
Another new OWL VIEW Camera Comparison
I just replaced my IR 4MP Uniview with a Uniview 4MP Owl View WISE camera. The IPC2B14SE-ADF28K-WP-I1 captures video up to a resolution of 4MP @ 30 fps, which is 2688 x 1520 pixels. The price was $359, which I found on a website and sold by a Security Company in Los Angeles. I have seen this... -
Anybody else having rodents (squirrels, rats, etc.) nesting underhood and/or chewing on wiring?
Ford Fusion, got in to drive to store. WTF the engine is misfiring and barely running. Opened the hood and found the rat's nest, acorns, shredded hood insulation, and the wiring harness was chewed through. A new wiring harness for my 2012 (old) has to be special ordered, or not in stock. And... -
Warm LED Camera Light
I have a Uniview Owl VIew which has the 1/1.8 shutter, and "warm light". There are no IR lights. The white light is not on all the time, and (on my camera) you can disable if you wish. This would be the option if the camera is at a place which has good surrounding lights (ie. parking lot... -
New Uniview Owl Wise color IP camera vs IR camera
This is with the "white light" on -
New Uniview Owl Wise color IP camera vs IR camera
No. It is a screen shot on the UI3 taken at 2 AM This was the night of the full moon which was directly behind the outbuilding I have the camera mounted on. Our house is a very light cream color (almost light yellow) and I was totally amazed at the image. Yes it looks like daylight. Here is... -
New Uniview Owl Wise color IP camera vs IR camera
It's not a sidewalk. Nobody is in the backyard at 2AM so no video of people. There is some motion blur when there is no full moon and the "white light" is not on. With the camera light on, or full moon there is virturally no motion blur. I just installed the camera so I don't have much... -
New Uniview Owl Wise color IP camera vs IR camera
I upgaded from the UNI 4MP 2.8mm Bullet (IPC2124SR3-ADPF28M-F) to the new UNV Owl Wise 4MP 2.8mm Bullet (IPC2314SR-ADF28KM-WP) "night vision". Wow. Here are two side by side. The BW infrared vs the Color Owl Wise. Both are at 02:00 AM, the Owl WIse was with no "smart illumination -(off) and... -
One camera "no video" for unexplained 6+ hour gap
UniFi let me set IP for any device as static Both the router and UNIVIEW camera configuration are matched static IP’s DHCP is off at both ends for the cameras The pool is wide open but that’s irrelevant using static as I understand it- Andykev
- Post #7
- Forum: Troubleshooting
-
One camera "no video" for unexplained 6+ hour gap
"Possibility" something to do with router? The Unifi did not have a static IP set, but I remember setting one for each Cam 1 and Cam 2. But today only Cam 1 had the static IP so perhaps something happened? Will monitor it, and it has been reset to static.- Andykev
- Post #5
- Forum: Troubleshooting
-
One camera "no video" for unexplained 6+ hour gap
I don't think the IR died... sunrise and daylight was well before the 8:42 AM when the camera suddenly resumed recording. I checked all the settings on the camera interface and nothing changed. I don't think the camera has a log, not sure will check. The cameras are on static IP's.- Andykev
- Post #4
- Forum: Troubleshooting
-
One camera "no video" for unexplained 6+ hour gap
I checked the video this morning and discovered that one of my cameras (I only run two!) stopped recording about 1AM and showed "no video" and then began recording around 8AM. Camera 1 had no interruptions, just Camera 2. I checked the database logs and rebuilt the DB but there were no apparent...- Andykev
- Thread
- Replies: 8
- Forum: Troubleshooting
-
I upgraded to Windows 11, new CPU, Memory, and a Motherboard - Success!
I am using the Cooler Master HAF XB which you can open on sides and the top Looks like a test bench layout and support for 4 WDPurple and 3 SSD lots of room- Andykev
- Post #9
- Forum: General BI Talk
-
I upgraded to Windows 11, new CPU, Memory, and a Motherboard - Success!
I decided to upgrade just my CPU, memory, and Motherboard. I was on an older I7-6700, which worked fine... but I the annoying "Windows end of life" messages...time to upgrade to Windows 11 (which I use on my laptop and main computers). The current CPU and motherboard were not eligible for the...- Andykev
- Thread
- Replies: 9
- Forum: General BI Talk
-
Camera IP changed on it's own
Excellent information. My search words did not pull up this known issue (I tried looking first before posting). So I can roll back, should it be 5.6.2 or an earlier version? He said "newer than" so I want to be sure. I don't need to be a "beta tester" :)- Andykev
- Post #8
- Forum: Troubleshooting
-
Camera IP changed on it's own
I am on 5.7.9.6 Here is the BI log and it changed the IP to something I do not have... 192.168.0.13- Andykev
- Post #6
- Forum: Troubleshooting
-
Camera IP changed on it's own
BTW I am using Ubiquiti UDM and the cameras are set to fixed IP's. I went back and looked at the BI Log again and the IP showed access by the IP for my Iphone... but I have no idea why that happened. I did not log in remotely that morning. Stumped.- Andykev
- Post #5
- Forum: Troubleshooting
-
Camera IP changed on it's own
NO I have updates turned off, have been for months. I'll check those links. Thank you.- Andykev
- Post #3
- Forum: Troubleshooting
-
Camera IP changed on it's own
A few days ago my IP address for CAM 1 changed on it's own to the IP address for CAM 2. I am only running two Uniview 4K cameras on BI with CPAI. Never a problem. We were not home, so I can't understand why CAM 1 suddenly began recording with the IP of CAM 2...so I ended up with duplicate...- Andykev
- Thread
- Replies: 9
- Forum: Troubleshooting
-
Power outage mini-diasater
It’s a I7-6700 Gigabyte Z170 probably 8 years old Maybe? -
Power outage mini-diasater
I did not think a 45 minute power outage on a 107 degree day would cause all kinds of problems with Blue Iris and the Code AI.!! Yes I am on a Cyberpower 1500va battery backup. When the power came back on, the Code AI did not work, the cameras were showing video feed but zero "triggers". Also... -
Nvidia big headache lost my Code AI detection
First, I got things back working. However I removed the Nvidia GTX 1650 from the computer and switched Code AI to "CPU" as well as the associated settings in BI. Yesterday, I got the "popup" to update the software for the Nvidia card (nothing unusual about that) with the "game ready" drivers... -
I keep getting "Nothing Found"
I did the install yesterday... the only thing I did which "may" have kicked it into gear was I "unchecked" the USE GPU and then rebooted, the rechecked it. I am using a Nvidia GTX1650 so it should have plenty of horsepower to run two cameras. My CPU is an I7-6700 with 32g RAM so I don't think... -
I keep getting "Nothing Found"
Now I have become completely baffled.... just like that it has started working. I have no clue... did not change anything. The "ALERTS" are showing in the left column and the LOGS show detection. OMG -
-
I keep getting "Nothing Found"
My system failed detection a couple days ago using DeepStack, so I switched to Code AI. It seems that I installed things correctly per instructions, and the server is running fine. However all objects are "nothing found" and Blue Iris won't post anything in the "ALERTS". Is something missing...