Search results

  1. I

    Is IPC-T5442T-ZE still the best bang for the buck

    Thanks. That sounds great.
  2. I

    Is IPC-T5442T-ZE still the best bang for the buck

    I did a search and found the same question asked, but it ended over a year ago. Since a year has passed, has there been any changes? Is the IPC-T5442T-ZE still the best bang for the buck?
  3. I

    DH-SD59225U-HNI PTZ control works in dahua gui but not in BI?

    My DH-SD59225U-HNI can't be controlled when I try to run the PTZ controls with BI. When I go into the camera GUI the PTZ controls work fine. What happened? Has anyone experienced that before? I'm sure I must have done something along the line, but really haven't messed with anything that I know of.
  4. I

    What do most of you do for runs over 350 feet?

    Well, I just went and talked to him and I think I have it figured out on what we can do. I'm going to be moving the switch and power to the other side of the totally enclosed building. That will put it 70' closer to the farthest away PTZ camera. I told him that was the only way we could get it...
  5. I

    What do most of you do for runs over 350 feet?

    Not at this time that I know of. It is mainly just to park the equipment in to get out of weather.
  6. I

    What do most of you do for runs over 350 feet?

    That's all dependent on how much more he wants to spend doing this. It's not like it is cheap to build this building and will take a lot to get it wired since is is not an inside finished building. It would take hundreds of feet of conduit and electrical wire, and electricians. Probably a...
  7. I

    What do most of you do for runs over 350 feet?

    Well, unless I can get power to the points I would need it, the only thing that will be able to run, will be cat6 cable. I won't know until the building is finished to know how the facility will look for sure and if he is even planning on running any type of electricity to any parts of it.
  8. I

    What do most of you do for runs over 350 feet?

    It may be that he can't run as long as he wants me to. This is in an outdoor metal building. It will be a storage facility for all of his large equipment. It is 3/4 covered. The front is open and exposed to the elements. The way it is setup it will be hard to add power to a lot of the places...
  9. I

    What do most of you do for runs over 350 feet?

    My friend wants to put a camera at the far end of his building and up at the top. The building is 20' high, and 320' from the source. The cable run will be around 360 when all things are said and done with the up and down walls etc. What would you do to make this work properly? I have run a lot...
  10. I

    Camera goes on/off on hot days.

    What is the distance of the run?
  11. I

    How do I setup motion detection on my PTZ5A4M-25X

    I've got to redo an older PTZ that I had to reset. It has been so long, that I'll have to try to remember how I did it over 2 years ago. My memory sucks. I'm sure it will be somewhat similar though.
  12. I

    How do I setup motion detection on my PTZ5A4M-25X

    Thank you so much. I hadn't found that video yet. I probably would have, but it may have been next week ;). I so do appreciate it. Have a great day.
  13. I

    How do I setup motion detection on my PTZ5A4M-25X

    Its the new gui.
  14. I

    How do I setup motion detection on my PTZ5A4M-25X

    I just got 2 new PTZ5A4M-25X , but I can't seem to figure out how to get them to detect motion and track. I will keep looking for the settings in the meantime and see what I find. Thanks.
  15. I

    SD5A425XA-HNR PTZ controls won't work.

    Well, I unplugged the power from the PTZ for a short time. I plugged it back in, and it now works again. Crazy. Well, it works. Now I need to start another post for a different PTZ I just got. Thanks for your help.
  16. I

    SD5A425XA-HNR PTZ controls won't work.

    I flashed firmware recently, but it was firmware directly from Andy for the PTZ version I gave him. I did 2 of them. One works, the other doesn't. Although, I flashed it a week ago, and it only quit working yesterday.
  17. I

    SD5A425XA-HNR PTZ controls won't work.

    The camera is 690 day(s) 7 hour(s) 30 minute(s) . It was not on a tour cycle. It should last longer than that I would hope. Maybe it is user error and I did something to a setting that I am not aware of. I can't find anything though.
  18. I

    SD5A425XA-HNR PTZ controls won't work.

    My SD5A425XA-HNR ptz controls just stopped working. I can't them to respond at all. No, zoom or pan or anything. What could have happened? Has anyone experienced this before? Thanks.
  19. I

    PTZ cam with as good optics or better as IPC-T5442T-EZ.

    Yes, it must be good. Or it better be good for that price. ;)
  20. I

    PTZ cam with as good optics or better as IPC-T5442T-EZ.

    Our setup has to be PoE. The run of cable is going to be around 125' or so. There are not a lot of options for more electricity and such, and it is already wired for PoE. I talked to Andy about that camera, and he says it is not PoE. I don't think there are any other options of a camera like...
View older results
Top Bottom