Search results

  1. M

    New here.

    I’ll have to get one and check it out. Thanks.
  2. M

    New here.

    Ok. Thanks. I see that it sends signal to base to sound alarm and lights. Wondering if there is a way to tap into the base to actually hardwire like a stand alone pir to my nvr or camera.
  3. M

    New here.

    Do you have these wired to your NVR or Cameras for alerts?
  4. M

    POE splitter usage

    That’s the exact behavior that I was expecting also but it’s not the case. I Recently replaced the pigtail on this camera and I’m wondering if I miss wired it to cause that to happen.
  5. M

    POE splitter usage

    I got this DC18V-60V to 12V Buck converter Passive PoE Splitter Cable Power Over Ethernet | eBay to use on my hikvision cam cause I thought I fried the poe board. Turns out I didnt fry it and poe works fine. However when i plug the cable from the poe switch into this device,then ONLY plug the...
  6. M

    replacement Hikvision pigtail

    Thank you very much. Good advice with the desiccant.
  7. M

    replacement Hikvision pigtail

    Tested the cable on camera on the bench,and it works. I dont have the thick black or red wires connected. Is there a place for these? Or just leave them disconnected. Also is there a place to connect the wire from the LED light on plug on the hikvision?
  8. M

    replacement Hikvision pigtail

    The exact cable i got is no longer available but there are similar ones. https://www.ebay.com/itm/POE-LAN-IP-cable-for-CCTV-IP-camera-board-module-weatherproof-connector/264061904794?epid=19019844636&hash=item3d7b50e79a:g:ttMAAOSw6CRb~RDx I have not installed the cable yet.
  9. M

    replacement Hikvision pigtail

    Yes , i'm sorry 4,5 are connected as well as 7,8
  10. M

    replacement Hikvision pigtail

    Retested,I'm an idiot. I had pin order backwards.I measured pin 1 as 8 and 8 as 1. So I do have pins 1,2,3,6. So i should be good right?
  11. M

    replacement Hikvision pigtail

    Yes I am. I'll have to retest my findings. The other thing I thought was unusual was that the Thick red and black wires were attached to the 12v plug,which i expected but the thinner red and black were also connected to the 12v plug.Not to the rj45 plug.
  12. M

    replacement Hikvision pigtail

    I just got a similar cable from ebay. 11 wires. I assumed 8 wires for rj45 plug, 2 wires for 12v power and the last for the led on plug.It didn't come with pinout chart so I used multimeter to check each one. Pin 2 and pin 5 aren't connect to anything. The camera i'm using it on has a bad poe...
  13. M

    Email setup not working with DS-2CD2642FWD-IZS

    It's working now. On the 2032, i didn't need to input receiver's name for it to work, but on the 2642 I put in receiver's name and it worked. Authentication isn't checked and username and PW not inputted on either Camera. I have no idea why doesn't need it but it works.
  14. M

    Email setup not working with DS-2CD2642FWD-IZS

    2032 settings that work,when i put same info in 2642 cam i get device error
  15. M

    [FS] NEW - LTS 4MP Bullet Motorized 2.8mm-12mm

    Still available?
  16. M

    Email setup not working with DS-2CD2642FWD-IZS

    I've got a DS-2CD2642FWD-IZS with firmware V5.5.82 build 190220 that i can't get email setup. Keep getting device error. I'm using the same settings which work for my DS-2CD2032-I with firmware V5.4.5 build 170123. Any thoughts why?
  17. M

    Unforwarding ports?

    A factory reset worked. Thank you.
  18. M

    Unforwarding ports?

    Both devices power cycled. Yes to question 2. Previously had ports open/forwarded and recently decided to close them.
  19. M

    Unforwarding ports?

    Nothing enabled or checked for DMZ
  20. M

    Unforwarding ports?

    UPnP turned off
  21. M

    Unforwarding ports?

    I have a hikvision ds7608NI-E2 NVR. When i go to canyouseeme.org and check the 8000, 554 ports it shows they are open. 80 and 443 are closed. If i turn off my NVR the port scan then shows they are closed. In my network setting nothing is enable except NTP and email. My router is netgear WGR 614...
  22. M

    What Software To Use To Change Internal Camera Settings

    That function is available in the hik nvr menu under Record/Parameters.
  23. M

    What Software To Use To Change Internal Camera Settings

    Just to clarify,It is true i can access my camera internals thru my NVR. Just not all the settings as I can from the web browser.
  24. M

    What Software To Use To Change Internal Camera Settings

    Is that possible with my non POE nvr? if so how?
  25. M

    What Software To Use To Change Internal Camera Settings

    There is no way to "get access to my Hikvision internals" using the actual NVR itself. You can only do that using the web browser to access your NVR which then provides a link to "get access to my Hikvision internals",(after you have enabled virtual host) under the System/Camera management...
  26. M

    Good source to buy IP items at

    Hi i'm interested in 3mp cams with alarm and audio inputs 6mm lens preferred
  27. M

    Question for owners of Hikvision NVR with alarm inputs.

    Im looking to get a Hikvision nvr with alarm inputs to use a PIR sensor with. I believe the DS-7716NI and the DS-7608NI-I2 are the ones that have this feature. To anyone who owns one of these and uses the alarm inputs with a PIR sensor, can you tell me if the email function correctly works and...
  28. M

    How to use Hikvision Audio and Alarm IO connections

    Unfortunately the the 7608 NVR I have doesnt have the alarm inputs.
  29. M

    How to use Hikvision Audio and Alarm IO connections

    How does this sealevel device work? I have PIR sensors that I use in my analog camera setup. But im now getting into the IP camera setup. I currently own 3 Hik 2cd2032 cameras and a Hik 7608 NVR. Would this device allow me to connect my PIR sensors to my Hik NVR to trigger recording,etc?
  30. M

    Returning defective DS-2CD2032 camera

    Ah Ok Understood Thank you.
Top Bottom