Recent content by RubberDinero

  1. R

    Can't access WUI, but RTSP will stream

    With the one I assigned 192.168.0.100
  2. R

    Can't access WUI, but RTSP will stream

    I have a generic IP camera, the instructions say to use PanoEagle AjDevTools, so I'm assuming it's some kind of clone. Strange thing about this camera is that it comes with a static IP from factory of 192.168.1.110, my network is 192.168.0.X, but I was able to log in to the web interface by...
  3. R

    Bricked SV3C IP 1080P Firmware help

    Can you upload the version of the program you have. I've tried a 1.29 version but it would never read
  4. R

    Bricked SV3C IP 1080P Firmware help

    at first I was using 1.18 and then i found 1.29. do you have a more recent version?
  5. R

    Bricked SV3C IP 1080P Firmware help

    Well, after desoldering and connecting it to my chip reader. Nothing, nada. same as if it were still plugged in. Maybe this reader is just not compatible. Don't know. I've officially given up. No way to program this chip.
  6. R

    Bricked SV3C IP 1080P Firmware help

    I read in another place that the reason some chips can't be read in parallel is because when you input the VCC voltage, it sends that to the board and tries to boot. There are some solutions, you could put a 1000ohm resister before the nearest power source to the VCC to prevent the voltage from...
  7. R

    Bricked SV3C IP 1080P Firmware help

    Yeah, powered off and disconnected from everything. My next idea will be to take the chip off completely and see if it will read. Another issue is that the programmer I'm using doesn't list an MX25L6436, only matches up to MX25L64... the rest don't come close. I'll take the chip off and see if...
  8. R

    Bricked SV3C IP 1080P Firmware help

    Well, I tried and tried again and this programmer is not reading the chip. It won't detect it, it won't read it. Maybe i need better instructions. I tried hooking everything up before inserting the USB and many, many other things and that chip won't read.
  9. R

    Rookie needs help

    You could use no-ip.com and forward a port on your router. On your phone you would put the web address created at no-ip.com and port from router. In my Milestone Argus (WD NAS Server App), I have no-ip.com as madeupname.sytes.net:6000(not my real address or port). But my Argus software is user...
  10. R

    Bricked SV3C IP 1080P Firmware help

    In all honesty, I could have just purchased another $40 camera instead of all these flashing equipment and thrown the camera in the trash. But I am enjoying this, great learning experience. Also, I'll be able to help friends if they ever have the need to flash a chip.
  11. R

    Bricked SV3C IP 1080P Firmware help

    On the way tuesday. I've definitely put the lens back on. But during reading and flashing I'll have to remove it. hopefully no dust falls in. I know it's cheaper on ebay, but I've had better experience with Amazon and shipping is usually faster. If this works, I'll post the complete dump just...
  12. R

    Bricked SV3C IP 1080P Firmware help

    Here is a picture of the other side because all the info i found on that 8-pin led to a 16kb memory chip. the MX25L6436F chip seems like the main memory.
  13. R

    Bricked SV3C IP 1080P Firmware help

    I've seen these devices, but i have not seen how they use it without taking the chip off. I've always seem them take it off
  14. R

    Bricked SV3C IP 1080P Firmware help

    I'm all for it! I'll have to order it. I'm not a very good solder-er, is there a way to read from it without desoldering?
  15. R

    Bricked SV3C IP 1080P Firmware help

See more
Top Bottom