Recent content by maximus rezzus

  1. M

    Hikvision poe and ip camera

    Those are dahua cameras. They will not work plug and play with hikvision nvr (manufactures blocks plug and play cameras from other manufactures) what you need to do is to put them on a poe switch and on the same network. you need cameras' password. you need to be able to re-ip dahua cameras to...
  2. M

    Hikvision poe and ip camera

    You might need to get in touch with whoever you got those cameras from for password reset. However, depends on camera model, there might be a hard reset button somewhere on the camera - you have not posted camera model so I have no idea - if they do have reset button. most likely on the same...
  3. M

    Hikvision poe and ip camera

    For plug and play cameras like you have at the moment, the password of cameras and nvr must match. I would assume nvr 1 + cams have diff passwords and nvr 2 + cams have same pw so they would show up
  4. M

    Hikvision panocam and hikvision NVR. How to enable/detect external microphone

    I read the spec sheet, that camera has built-in microphone and speaker. You do not need external speaker. Spec sheet: https://www.hikvision.com/en/products/IP-Products/Network-Cameras/Pro-Series-EasyIP-/ds-2cd2387g2p-lsu-sl/?subName=DS-2CD2387G2P-LSU%2FSL+%28C%29+%28Black%29
  5. M

    How to get in to the camera settings

    1/ Download and install hikvision SADP software on your PC 2/ Make sure PC and NVR are on the same network 3/ Open SADP. If PC / NVR are on the same network, your NVR will show up on SADP 4/ Go to the NVR IP address shown on SADP 5/ Once you open up web browser, go to Configuration on the top...
  6. M

    Hikvision NVR can't add cameras - very weird problem

    Have you try to put both of them on a POE switch and add them using local IP address instead of plug and play to the back of NVR ?
  7. M

    Same old story. Updated Firmware on DS-7716NI-I4/16P now can't get in.

    where are your laptop and cams connected to ? are they on same network ?
  8. M

    Same old story. Updated Firmware on DS-7716NI-I4/16P now can't get in.

    if you unplug and plug the power back, cameras would flash / make a sound / red button flash somewhere at the front soooo if none of those happens, I have a bad new for you. especially if they are not showing up on SADP while being on the same network as the laptop
  9. M

    Hik-Connect Platform Access is offline for some cameras, but not for all

    Not sure if anyone help you out just yet. Are these 2 offline cams stand-alone cams or are they connected to an NVR ? Not sure if this would help but under Preferred DNS server, change it to the exact IP address of the Gateway IP address and change the Alternate DNS server to 8.8.8.8
  10. M

    Same old story. Updated Firmware on DS-7716NI-I4/16P now can't get in.

    Also, if you hover your mouse over, right on top of it, it will tell you whats wrong with it - Abnormal Network - Wrong username / password - No connection - to name a few
  11. M

    DS-2CD2443G0-IW cannot do motion detection recording

    i dont think so. If you click "clear all" all your red boxes will be gone. then he has to re-draw area of recording
  12. M

    Same old story. Updated Firmware on DS-7716NI-I4/16P now can't get in.

    192.168.254.xxx is IP address when you connect camera to NVR. So all of these are plugged into NVR. With that being said, you wont see them in SADP. Unplug them from NVR and plug them into POE switch with your laptop / computer plugged into the same POE switch to determine if your camera(s) is...
  13. M

    DS-2CD2443G0-IW cannot do motion detection recording

    Change sensitivity to 60. It looks like you already drew the area you want to record (red squares) Walk around and give it 5-10 minutes to see if it records
See more
Top Bottom