Recent content by HoosierD

  1. HoosierD

    Setup to allow NetTime to Work

    Not sure what happened. I reinstalled NetTime and bam, all times synced. Thanks for the time folks! Always appreciated and cannot praise this forum enough. I may not have many posts, but I probably have 100's of hours of my life with you guys in front of me.
  2. HoosierD

    Setup to allow NetTime to Work

    Thanks Mike. Yea, that's how I'm setup. This has taken on a new flavor. I enable debug level logging in NetTime, and see each camera reach in for a time. What is not happening, is the timestamp updating in the cameras. Overlays are for sure being added at the camera level and not BI. Outbound...
  3. HoosierD

    Setup to allow NetTime to Work

    New PC is the same IP address as the old PC. The cameras just don't seem to have a connection. I really don't want to roll timestamp into BI.
  4. HoosierD

    Setup to allow NetTime to Work

    I recently migrated my BI server to a new Win11 PC (from Win10). I just noticed that the cameras are not syncing with NetTime? I dug around here for a bit, turned off the Win11 time service, opened UDP port 123 in Win firewall, start/stop the service, did camera restarts, and I still can't get...
  5. HoosierD

    First LPR Layout. Feedback?

    Thanks everyone. Pictures are pending. I'm in CA and the property is TN.
  6. HoosierD

    First LPR Layout. Feedback?

    Hey folks, I'm wondering if I can get some expert feedback on my first LPR install. I have an appt building where we are having some trash dumping issues and need "proof" to have law enforcement intervention. There is only one way into this parking area, speeds will be “slow”, and area...
  7. HoosierD

    Dahua Relay Out - Wireless Door Sensor - Z-Wave Rule-Lights on!!!!

    Thanks @Smilingreen. Much appreciated. I've got a few 12V relays about and will be pulling the cam down to validate. Like you, after some thought, I'm wondering if the output is only powered when the cam uses external power (i.e. not POE). Tinkering will tell. Space is limited to my camera...
  8. HoosierD

    Dahua Relay Out - Wireless Door Sensor - Z-Wave Rule-Lights on!!!!

    My older Qolsys IQ2 panel took a dump after 6 years, so I updated to an IQ4 last week. I've purchased a few door/window sensors (wireless for those unaware) that have terminals for external contacts and I've setup a few around the house to be "monitor only" (i.e. side gate opens triggering...
  9. HoosierD

    Firmware issues

    Probably trying to flash the wrong firmware. What version are you trying?
  10. HoosierD

    Axis vs. Dahua

    I ran quite a few Axis IP PTZ cameras starting back in the beginning (around 2011). Now these were $3K-4K cameras at 720P resolution and simply amazing for the time. They were great in the day and accessible in the US. Now I know of Andy, I my entire flet is Dahua and I'll never go back.
  11. HoosierD

    Andy, I have request for the Dahua engineers, if it is possible to do

    Just use your signature. It lists all your cameras.
  12. HoosierD

    Best practise for time sync

    I too use my BI Server and NetTime as the NTP time source for all my cams. Zero open ports in todays world.
  13. HoosierD

    IPC-B5442E-ZE Login Issue After Firmware

    Alright. No clue what happened. I powered off for 10+ minutes, pushed reset on the cam in that period (to drain capacitance if present), cleared my cache, and I got in. Straight up no clue what happened there.
  14. HoosierD

    IPC-B5442E-ZE Login Issue After Firmware

    So I flashed General_IPC-HX5XXX-Volt_Eng_PN_Stream3_V2.800.0000000.1.R.190706 into my IPC-B5442E-ZE from Andy's link here , and now I can't log in? I can do a factory reset at the camera, go through the initialization, get the login screen, but once I add the new credentials, it hangs without...
  15. HoosierD

    Dahua day/night switch utility - DahuaSunriseSunset

    Good golly mis Molly. Noticed the service wasn't working any more, and to my amazement, the error log was 54GB. Deleted without even looking. Oops. Jumped to V1.6.0.0 and I can't connect to any camera (HDW2231RP's, HDW5231R's, or SD1A203T-GN)? I'm consistantly getting "The remote server...
See more
Top Bottom